Hi everyone i just purchased the combined speedo tach from harley, i am going to install it myself as looking at the instructions it looks straight forward, but my question is how do i remove the existing speedo from its housing on my 2013 1200custom, i have ordered a workshop manual but my dealer is saying 4 weeks delivery. Chrysler Marine 318 Service Manual on this page.J02257 REV. 11-26-03 ® Kit Numbers: 74460-03A, 74461-03A, 74462-03A, 74469-03A, 74471-03A, 74473-03A, 74475-03A, 74477-03A and 74479-03A SPEEDOMETER/ TACHOMETER COMBINATION GAUGE KIT General U.S. Department of Transportation The following kits are designed for direct speedometer National Highway Traffic Safety Administration. The codes I got are: for P – P0562 and P0563, for S – B0563, for SP – B1006 and B1007, for B – No RSP (I have a HD speedo/tach combo. I guess that means my voltage regulator is bad like btsom said.
![Davidson Davidson](https://www.autometer.com/media/catalog/product/cache/1/image/1500x/040ec09b1e35df139433887a97daa66f/1/2/1295_38.jpg)
![Combo Combo](https://www.dakotadigital.com/cartimages/prd_392.jpg?id=202003061355550)
- Both the ECM and speedometer retain the odometer value. If the speedometer is replaced, it displays the odometer value stored in the ECM. The replacement speedometer will become locked to the ECM after 31.1 miles (50 km) have been accumulated. The trip B odometer displays the countdown mileage. Once the countdown reaches zero, the speedometer is locked to the ECM. If installed on another vehicle the odometer displays 'VIN ERR'. If the speedometer is removed from the vehicle before the countdown reaches zero, it has not been locked to the ECM. This mileage countdown allows for a road test to verify that speedometer replacement was the proper repair.
- During the 50 km (31.1 mi) countdown period (before the speedometer is locked to the ECM), the security light flashes for up to 15 seconds when battery power is restored to the electrical system, while the new gauge synchronizes to the ECM.
- Gear Indication display is a calculated gear position based on wheel and engine speed. The gear position displayed may be momentarily inaccurate depending on rider clutch use characteristics and clutch wear. This momentary false reading, although unlikely, can occur if the clutch is allowed to slip either due to excessive wear, poorly adjusted clutch or if the operator rides the clutch.
- If gauge is installed on a motorcycle with ABS, TC, VHC, and/or TPMS, verify that the ABS, TC, VHC, and/or TPMS warning lamp is working properly. See the owner's manual for ABS, TC, VHC, and/or TPMS warning lamp operation.
- When ignition switch is turned from OFF or ACC to IGN, the needles will sweep the full range from zero to the maximum and back; background and needle colors will sweep through the full color range; all telltale indicators will illuminate momentarily.
Replacement Speedometer For Harley Davidson
- The replacement speedometer will become locked to the ECM after 31.1 miles (50 km) have been accumulated. The trip B odometer displays the countdown mileage. Once the countdown reaches zero, the speedometer is locked to the ECM. If installed on another vehicle the odometer displays 'VIN ERR'. If the speedometer is removed from the vehicle before the countdown reaches zero, it has not been locked to the ECM. This mileage countdown allows for a road test to verify that speedometer replacement was the proper repair.
- The 31.1 miles (50 km) countdown period (before the speedometer is locked to the ECM), the security light flashes for up to 15 seconds when battery power is restored to the electrical system, while the new gauge synchronizes to the ECM.
- Gear Indication display is a calculated gear position based on wheel and engine speed. The gear position displayed could be momentarily inaccurate depending on rider clutch use characteristics and clutch wear. This momentary false reading, although unlikely, can occur if the clutch is allowed to slip either due to excessive wear, poorly adjusted clutch or if the operator rides the clutch.
- If gauge is installed on a motorcycle with ABS, verify that the ABS warning lamp is working properly. See the owner's manual for ABS warning lamp operation.
- The odometer will display VIN ERR and the ABS warning lamp will illuminate if the gauge is installed on a non-ABS vehicle after the gauge is locked (accumulated 31.1 miles (50 km)) into an ABS vehicle.
- 2007 and earlier vehicles do NOT support the gear indicator display function.